

Core Specifications
Item |
Details |
|---|---|
Dell P/N |
0XCNHG / XCNHG (primary) |
Alt / Cross P/N |
AT30R002FFL · AT30R002DTL · DFS5K22305283D · FN56 · EG50040S1-CL90-S9A |
Compatible Models |
Dell Latitude 7320 (clamshell) Dell Latitude 7320 2-in-1 Dell Latitude E7320 (regional/retail naming) |
NOT Compatible With |
Latitude 7320 Detachable (uses different internal fans — DP/N 0DJ2D1 / 0PGV79, NOT this module) |
Voltage / Current |
DC 5V / 0.5A (2.5W) |
Connector |
4-pin, 4-wire PWM (wire-to-board) |
Airflow |
~2.0 CFM (blower style) |
Material |
Copper heatsink core + aluminum fin stack + plastic fan shroud |
Condition |
New third-party (PCparts), 100% tested |
Warranty |
45 Days — seller-level, not Dell factory |
Compatibility — The Critical Split (Read This First)
Variant |
Cooler Type |
Correct P/N |
This Listing Fits? |
|---|---|---|---|
7320 (clamshell laptop) |
Single fan + heatsink module |
0XCNHG / XCNHG |
YES
|
7320 2-in-1 |
Single fan + heatsink module |
0XCNHG / XCNHG |
YES
|
7320 Detachable (tablet) |
Two small internal fans (left + right) |
0DJ2D1 / 0PGV79 (Delta, 5-pin) |
NO
|
️ The "Detachable" is a totally different animal — it's a tablet with a keyboard base, uses two separate slim fans (DP/N 0DJ2D1 right / 0PGV79 variants), not this single-module heatsink assembly. If your machine is the Detachable, do not buy this listing — you need the DJ2D1/PGV79 fan pair.
How to confirm your variant:
Clamshell / 2-in-1 → bottom label reads "Latitude 7320" or "7320 2-in-1", has a normal hinged keyboard deck
Detachable → screen separates from keyboard base entirely, no fixed hinge; service tag pulls up "7320 Detachable"
️ What This Module Is / Isn't
Included |
NOT Included |
|---|---|
Fan + heatsink combined assembly |
Thermal paste / pad (you supply fresh paste) |
Mounting frame + screw bosses |
Mounting screws (usually transfer from old unit — M2×2.5 class) |
4-pin PWM connector with cable |
Dell OEM box / documentation |
Any other internal parts (battery, board, etc.) |
Always apply new thermal paste when swapping — reusing old dried paste kills the point of a new cooler.
Installation Difficulty: Medium-Low (Standard Dell Business Teardown)
Removal:
Shut down → disconnect AC → flip over, remove bottom cover
Disconnect battery ZIF first (critical — fan header is live even when powered off)
Disconnect fan cable from system board (small 4-pin)
Remove 2× M2×2.5 screws on the fan shroud
Remove 4× M2×2.5 screws securing the heatsink (Dell HMM specifies loosening in reverse order: 4→3→2→1 to avoid warping the sink)
Lift the assembly straight up — don't twist, the fins are soft copper
Install:
Clean old paste off CPU die with isopropyl + lint-free cloth
Apply pea-sized dot of quality paste (Arctic MX-4 / Honeywell PTM7950 if you want premium)
Seat new module, tighten heatsink screws in numbered order 1→2→3→4 (even torque, snug — don't crank)
Reconnect fan 4-pin (orientation matters — latch side matches)
Reconnect battery, close base, boot, check BIOS fan curve / HWMonitor
7320-Specific Pitfalls
Mistake |
Consequence |
|---|---|
Buying for a Detachable |
Wrong part entirely — Detachable uses 2 slim fans, not this module |
Forgetting battery disconnect |
Fan header live — risk of shorting the PWM circuit on reinstall |
Wrong screw order on heatsink |
Dell specs reverse-order loosen / forward-order tighten — criss-cross pattern; uneven torque warps the sink → bad contact → thermal throttle |
Reusing old paste |
Dry crust = hotspots, 95°C bounce, fan ramps to jet-engine |
Plugging 4-pin backwards |
Connector is keyed, but forced wrong = no fan spin / BIOS error |
Mixing fan batch P/Ns |
Fine physically (XCNHG/AT30R/fan56 all same profile), but match the connector pitch — all are 4-wire 5V 0.5A, so safe |
Package Contents (Typical)
1× CPU Cooling Fan + Heatsink Module (0XCNHG profile)
(Screws — usually NOT included; transfer your old M2×2.5 set)
Pre-Purchase Checklist
[ ] Machine is Latitude 7320 clamshell or 7320 2-in-1 (NOT Detachable)
[ ] Bottom-label / service tag confirms "7320" non-detachable
[ ] Original fan sticker reads 0XCNHG / XCNHG / AT30R002FFL / FN56 / DFS5K… (any of these = same module)
[ ] Symptom is actually the cooler:
Fan grinding / rattling / no spin → this part
Overheating / thermal throttle / 100°C shutdowns → this part (assuming paste+paste contact)
If no display / no POST → likely motherboard, not fan
If Detachable → need DJ2D1 / PGV79 fans instead
[ ] Have thermal paste + Phillips #00 / small JIS driver ready
Bottom Line









